Virtual filesystem (VFS) component provides a unified interface for drivers which can perform operations on file-like objects. This can be a real filesystems (FAT, SPIFFS, etc.), or device drivers which exposes file-like interface.
This component allows C library functions, such as fopen and fprintf, to work with FS drivers. At high level, each FS driver is associated with some path prefix. When one of C library functions needs to open a file, VFS component searches for the FS driver associated with the file's path, and forwards the call to that driver. VFS also forwards read, write, and other calls for the given file to the same FS driver.
For example, one can register a FAT filesystem driver with ``/fat`` prefix, and call ``fopen("/fat/file.txt", "w")``. VFS component will then call ``open`` function of FAT driver and pass ``/file.txt`` argument to it (and appropriate mode flags). All subsequent calls to C library functions for the returned ``FILE*`` stream will also be forwarded to the FAT driver.
Each registered FS has a path prefix associated with it. This prefix may be considered a "mount point" of this partition.
Registering mount points which have another mount point as a prefix is not supported and results in undefined behavior. For instance, the following is correct and supported:
VFS doesn't impose a limit on total file path length, but it does limit FS path prefix to ``ESP_VFS_PATH_MAX`` characters. Individual FS drivers may have their own filename length limitations.
File descriptors
----------------
It is suggested that filesystem drivers should use small positive integers as file descriptors. VFS component assumes that ``CONFIG_MAX_FD_BITS`` bits (12 by default) are sufficient to represent a file descriptor.
If filesystem is configured with an option to offset all file descriptors by a constant value, such value should be passed to ``fd_offset`` field of ``esp_vfs_t`` structure. VFS component will then remove this offset when working with FDs of that specific FS, bringing them into the range of small positive integers.
While file descriptors returned by VFS component to newlib library are rarely seen by the application, the following details may be useful for debugging purposes. File descriptors returned by VFS component are composed of two parts: FS driver ID, and the actual file descriptor. Because newlib stores file descriptors as 16-bit integers, VFS component is also limited by 16 bits to store both parts.
Lower ``CONFIG_MAX_FD_BITS`` bits are used to store zero-based file descriptor. If FS driver has a non-zero ``fd_offset`` field, this ``fd_offset`` is subtracted FDs obtained from the FS ``open`` call, and the result is stored in the lower bits of the FD. Higher bits are used to save the index of FS in the internal table of registered filesystems.
When VFS component receives a call from newlib which has a file descriptor, this file descriptor is translated back to the FS-specific file descriptor. First, higher bits of FD are used to identify the FS. Then ``fd_offset`` field of the FS is added to the lower ``CONFIG_MAX_FD_BITS`` bits of the fd, and resulting FD is passed to the FS driver.
If "UART for console output" menuconfig option is not set to "None", then ``stdin``, ``stdout``, and ``stderr`` are configured to read from, and write to, a UART. It is possible to use UART0 or UART1 for standard IO. By default, UART0 is used, with 115200 baud rate, TX pin is GPIO1 and RX pin is GPIO3. These parameters can be changed in menuconfig.
Writing to ``stdout`` or ``stderr`` will send characters to the UART transmit FIFO. Reading from ``stdin`` will retrieve characters from the UART receive FIFO.
Note that while writing to ``stdout`` or ``stderr`` will block until all characters are put into the FIFO, reading from ``stdin`` is non-blocking. The function which reads from UART will get all the characters present in the FIFO (if any), and return. I.e. doing ``fscanf("%d\n", &var);`` may not have desired results. This is a temporary limitation which will be removed once ``fcntl`` is added to the VFS interface.
Standard streams and FreeRTOS tasks
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
``FILE`` objects for ``stdin``, ``stdout``, and ``stderr`` are shared between all FreeRTOS tasks, but the pointers to these objects are are stored in per-task ``struct _reent``. The following code::
fprintf(stderr, "42\n");
actually is translated to to this (by the preprocessor):
where the ``__getreent()`` function returns a per-task pointer to ``struct _reent`` (:component_file:`newlib/include/sys/reent.h#L370-L417>`). This structure is allocated on the TCB of each task. When a task is initialized, ``_stdin``, ``_stdout`` and ``_stderr`` members of ``struct _reent`` are set to the values of ``_stdin``, ``_stdout`` and ``_stderr`` of ``_GLOBAL_REENT`` (i.e. the structure which is used before FreeRTOS is started).
- It is possible to set ``stdin``, ``stdout``, and ``stderr`` for any given task without affecting other tasks, e.g. by doing ``stdin = fopen("/dev/uart/1", "r")``.
- Closing default ``stdin``, ``stdout``, or ``stderr`` using ``fclose`` will close the ``FILE`` stream object — this will affect all other tasks.
- To change the default ``stdin``, ``stdout``, ``stderr`` streams for new tasks, modify ``_GLOBAL_REENT->_stdin`` (``_stdout``, ``_stderr``) before creating the task.
