OVMS3-idf/components/esp32/include/xtensa/xtav200.h

281 lines
10 KiB
C
Raw Normal View History

2016-08-17 15:08:22 +00:00
/* Copyright (c) 2007-2013 by Tensilica Inc. ALL RIGHTS RESERVED.
/ These coded instructions, statements, and computer programs are the
/ copyrighted works and confidential proprietary information of Tensilica Inc.
/ They may not be modified, copied, reproduced, distributed, or disclosed to
/ third parties in any manner, medium, or form, in whole or in part, without
/ the prior written consent of Tensilica Inc.
*/
/* xtav200.h - Xtensa Avnet LX200 (XT-AV200) board specific definitions */
#ifndef _INC_XTAV200_H_
#define _INC_XTAV200_H_
#include <xtensa/config/core.h>
#include <xtensa/config/system.h>
#define XTBOARD_NAME "XT-AV200"
/*
* Default assignment of XTAV200 devices to external interrupts.
*/
/* Ethernet interrupt: */
#ifdef XCHAL_EXTINT1_NUM
#define ETHERNET_INTNUM XCHAL_EXTINT1_NUM
#define ETHERNET_INTLEVEL XCHAL_EXTINT1_LEVEL
#define ETHERNET_INTMASK XCHAL_EXTINT1_MASK
#else
#define ETHERNET_INTMASK 0
#endif
/* UART interrupt: */
#ifdef XCHAL_EXTINT0_NUM
#define UART16550_INTNUM XCHAL_EXTINT0_NUM
#define UART16550_INTLEVEL XCHAL_EXTINT0_LEVEL
#define UART16550_INTMASK XCHAL_EXTINT0_MASK
#else
#define UART16550_INTMASK 0
#endif
/* Audio output interrupt (I2S FIFO underrun): */
#ifdef XCHAL_EXTINT2_NUM
#define AUDIO_INTNUM XCHAL_EXTINT2_NUM
#define AUDIO_INTLEVEL XCHAL_EXTINT2_LEVEL
#define AUDIO_INTMASK XCHAL_EXTINT2_MASK
#else
#define AUDIO_INTMASK 0
#endif
/* Audio output (I2S FIFO level) interrupt: */
#ifdef XCHAL_EXTINT3_NUM
#define AUDIO_I2SLVL_INTNUM XCHAL_EXTINT3_NUM
#define AUDIO_I2SLVL_INTLEVEL XCHAL_EXTINT3_LEVEL
#define AUDIO_I2SLVL_INTMASK XCHAL_EXTINT3_MASK
#else
#define AUDIO_I2SLVL_INTMASK 0
#endif
/* Audio input (ADC FIFO level) interrupt: */
#ifdef XCHAL_EXTINT4_NUM
#define AUDIO_ADCLVL_INTNUM XCHAL_EXTINT4_NUM
#define AUDIO_ADCLVL_INTLEVEL XCHAL_EXTINT4_LEVEL
#define AUDIO_ADCLVL_INTMASK XCHAL_EXTINT4_MASK
#else
#define AUDIO_ADCLVL_INTMASK 0
#endif
/*
* Device addresses.
*
* Note: for endianness-independence, use 32-bit loads and stores for all
* register accesses to Ethernet, UART and LED devices. Undefined bits
* may need to be masked out if needed when reading if the actual register
* size is smaller than 32 bits.
*
* Note: XTAV200 bus byte lanes are defined in terms of msbyte and lsbyte
* relative to the processor. So 32-bit registers are accessed consistently
* from both big and little endian processors. However, this means byte
* sequences are not consistent between big and little endian processors.
* This is fine for RAM, and for ROM if ROM is created for a specific
* processor (and thus has correct byte sequences). However this may be
* unexpected for Flash, which might contain a file-system that one wants
* to use for multiple processor configurations (eg. the Flash might contain
* the Ethernet card's address, endianness-independent application data, etc).
* That is, byte sequences written in Flash by a core of a given endianness
* will be byte-swapped when seen by a core of the other endianness.
* Someone implementing an endianness-independent Flash file system will
* likely handle this byte-swapping issue in the Flash driver software.
*/
#define XTBOARD_FLASH_MAXSIZE 0x1000000 /* 16 MB */
#ifdef XSHAL_IOBLOCK_BYPASS_PADDR
/* Flash Memory: */
# define XTBOARD_FLASH_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x08000000)
/* FPGA registers: */
# define XTBOARD_FPGAREGS_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0D020000)
/* Ethernet controller/transceiver SONIC SN83934: */
# define ETHERNET_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0D030000)
/* UART National-Semi PC16550D: */
# define UART16550_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0D050000)
/* TI 320AIC23/28-TSSOP Stereo Audio Codec: */
# define AUDIO_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0D070000)
/* Boot 128K Sram address: */
# define BOOT_SRAM_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0D400000)
/* Ethernet buffer: */
# define ETHERNET_BUFFER_PADDR (XSHAL_IOBLOCK_BYPASS_PADDR+0x0D800000)
#endif /* XSHAL_IOBLOCK_BYPASS_PADDR */
/* These devices might be accessed cached: */
#ifdef XSHAL_IOBLOCK_CACHED_PADDR
# define XTBOARD_FLASH_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0x08000000)
# define ETHERNET_BUFFER_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0x0D800000)
# define BOOT_SRAM_CACHED_PADDR (XSHAL_IOBLOCK_CACHED_PADDR+0x0D400000)
#endif /* XSHAL_IOBLOCK_CACHED_PADDR */
/*** Same thing over again, this time with virtual addresses: ***/
#ifdef XSHAL_IOBLOCK_BYPASS_VADDR
/* Flash Memory: */
# define XTBOARD_FLASH_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x08000000)
/* FPGA registers: */
# define XTBOARD_FPGAREGS_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0D020000)
/* Ethernet controller/transceiver SONIC SN83934: */
# define ETHERNET_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0D030000)
/* UART National-Semi PC16550D: */
# define UART16550_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0D050000)
/* TI 320AIC23/28-TSSOP Stereo Audio Codec: */
# define AUDIO_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0D070000)
/* 128K Sram address: */
# define BOOT_SRAM_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0D400000)
/* Ethernet buffer: */
# define ETHERNET_BUFFER_VADDR (XSHAL_IOBLOCK_BYPASS_VADDR+0x0D800000)
#endif /* XSHAL_IOBLOCK_BYPASS_VADDR */
/* These devices might be accessed cached: */
#ifdef XSHAL_IOBLOCK_CACHED_VADDR
# define XTBOARD_FLASH_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0x08000000)
# define AUDIO_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0x0D070000)
# define ETHERNET_BUFFER_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0x0D800000)
# define BOOT_SRAM_CACHED_VADDR (XSHAL_IOBLOCK_CACHED_VADDR+0x0D400000)
#endif /* XSHAL_IOBLOCK_CACHED_VADDR */
/* System ROM: */
#define XTBOARD_ROM_SIZE XSHAL_ROM_SIZE
#ifdef XSHAL_ROM_VADDR
#define XTBOARD_ROM_VADDR XSHAL_ROM_VADDR
#endif
#ifdef XSHAL_ROM_PADDR
#define XTBOARD_ROM_PADDR XSHAL_ROM_PADDR
#endif
/* System RAM: */
#define XTBOARD_RAM_SIZE XSHAL_RAM_SIZE
#ifdef XSHAL_RAM_VADDR
#define XTBOARD_RAM_VADDR XSHAL_RAM_VADDR
#endif
#ifdef XSHAL_RAM_PADDR
#define XTBOARD_RAM_PADDR XSHAL_RAM_PADDR
#endif
#define XTBOARD_RAM_BYPASS_VADDR XSHAL_RAM_BYPASS_VADDR
#define XTBOARD_RAM_BYPASS_PADDR XSHAL_RAM_BYPASS_PADDR
/*
* Things that depend on device addresses.
*/
#define XTBOARD_CACHEATTR_WRITEBACK XSHAL_XT2000_CACHEATTR_WRITEBACK
#define XTBOARD_CACHEATTR_WRITEALLOC XSHAL_XT2000_CACHEATTR_WRITEALLOC
#define XTBOARD_CACHEATTR_WRITETHRU XSHAL_XT2000_CACHEATTR_WRITETHRU
#define XTBOARD_CACHEATTR_BYPASS XSHAL_XT2000_CACHEATTR_BYPASS
#define XTBOARD_CACHEATTR_DEFAULT XSHAL_XT2000_CACHEATTR_DEFAULT
#define XTBOARD_BUSINT_PIPE_REGIONS XSHAL_XT2000_PIPE_REGIONS
#define XTBOARD_BUSINT_SDRAM_REGIONS XSHAL_XT2000_SDRAM_REGIONS
/*
* FPGA registers.
* All these registers are normally accessed using 32-bit loads/stores.
*/
/* Register offsets: */
#define XTBOARD_DATECD_OFS 0x00 /* date code (read-only) */
#define XTBOARD_CLKFRQ_OFS 0x04 /* clock frequency Hz (read-only) */
#define XTBOARD_SYSLED_OFS 0x08 /* LEDs */
#define XTBOARD_DIPSW_OFS 0x0C /* DIP switch bits (read-only) */
#define XTBOARD_SWRST_OFS 0x10 /* software reset */
/* Physical register addresses: */
#ifdef XTBOARD_FPGAREGS_PADDR
#define XTBOARD_DATECD_PADDR (XTBOARD_FPGAREGS_PADDR+XTBOARD_DATECD_OFS)
#define XTBOARD_CLKFRQ_PADDR (XTBOARD_FPGAREGS_PADDR+XTBOARD_CLKFRQ_OFS)
#define XTBOARD_SYSLED_PADDR (XTBOARD_FPGAREGS_PADDR+XTBOARD_SYSLED_OFS)
#define XTBOARD_DIPSW_PADDR (XTBOARD_FPGAREGS_PADDR+XTBOARD_DIPSW_OFS)
#define XTBOARD_SWRST_PADDR (XTBOARD_FPGAREGS_PADDR+XTBOARD_SWRST_OFS)
#endif
/* Virtual register addresses: */
#ifdef XTBOARD_FPGAREGS_VADDR
#define XTBOARD_DATECD_VADDR (XTBOARD_FPGAREGS_VADDR+XTBOARD_DATECD_OFS)
#define XTBOARD_CLKFRQ_VADDR (XTBOARD_FPGAREGS_VADDR+XTBOARD_CLKFRQ_OFS)
#define XTBOARD_SYSLED_VADDR (XTBOARD_FPGAREGS_VADDR+XTBOARD_SYSLED_OFS)
#define XTBOARD_DIPSW_VADDR (XTBOARD_FPGAREGS_VADDR+XTBOARD_DIPSW_OFS)
#define XTBOARD_SWRST_VADDR (XTBOARD_FPGAREGS_VADDR+XTBOARD_SWRST_OFS)
/* Register access (for C code): */
#define XTBOARD_DATECD_REG (*(volatile unsigned*) XTBOARD_DATECD_VADDR)
#define XTBOARD_CLKFRQ_REG (*(volatile unsigned*) XTBOARD_CLKFRQ_VADDR)
#define XTBOARD_SYSLED_REG (*(volatile unsigned*) XTBOARD_SYSLED_VADDR)
#define XTBOARD_DIPSW_REG (*(volatile unsigned*) XTBOARD_DIPSW_VADDR)
#define XTBOARD_SWRST_REG (*(volatile unsigned*) XTBOARD_SWRST_VADDR)
#endif
/* DATECD (date code; when core was built) bit fields: */
/* BCD-coded month (01..12): */
#define XTBOARD_DATECD_MONTH_SHIFT 24
#define XTBOARD_DATECD_MONTH_BITS 8
#define XTBOARD_DATECD_MONTH_MASK 0xFF000000
/* BCD-coded day (01..31): */
#define XTBOARD_DATECD_DAY_SHIFT 16
#define XTBOARD_DATECD_DAY_BITS 8
#define XTBOARD_DATECD_DAY_MASK 0x00FF0000
/* BCD-coded year (2001..9999): */
#define XTBOARD_DATECD_YEAR_SHIFT 0
#define XTBOARD_DATECD_YEAR_BITS 16
#define XTBOARD_DATECD_YEAR_MASK 0x0000FFFF
/* SYSLED (system LED) bit fields: */
/* LED control bits (off=0, on=1): */
#define XTBOARD_SYSLED_USER_SHIFT 0
#define XTBOARD_SYSLED_USER_BITS 4
#define XTBOARD_SYSLED_USER_MASK 0x0000000F
/* DIP Switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1): */
/* DIP switch bit fields (bit6/sw7 is reserved and presently unused): */
#define XTBOARD_DIPSW_USER_SHIFT 0 /* labeled 1-6 (1=lsb) */
#define XTBOARD_DIPSW_USER_BITS 6
#define XTBOARD_DIPSW_USER_MASK 0x0000003F
#define XTBOARD_DIPSW_BOOT_SHIFT 7 /* labeled 8 (msb) */
#define XTBOARD_DIPSW_BOOT_BITS 1
#define XTBOARD_DIPSW_BOOT_MASK 0x00000080
/* Boot settings: bit7/sw8, off=0, on=1 (this switch controls hardware): */
#define XTBOARD_DIPSW_BOOT_RAM (0<<XTBOARD_DIPSW_BOOT_SHIFT) /* off */
#define XTBOARD_DIPSW_BOOT_FLASH (1<<XTBOARD_DIPSW_BOOT_SHIFT) /* on */
/* SWRST (software reset; allows s/w to generate power-on equivalent reset): */
/* Software reset bits: */
#define XTBOARD_SWRST_SWR_SHIFT 0
#define XTBOARD_SWRST_SWR_BITS 16
#define XTBOARD_SWRST_SWR_MASK 0x0000FFFF
/* Software reset value -- writing this value resets the board: */
#define XTBOARD_SWRST_RESETVALUE 0x0000DEAD
#endif /*_INC_XTAV200_H_*/