OVMS3-idf/components/spi_flash/Kconfig

menu "SPI Flash driver"

    config SPI_FLASH_VERIFY_WRITE
        bool "Verify SPI flash writes"
        default n
        help
            If this option is enabled, any time SPI flash is written then the data will be read
            back and verified. This can catch hardware problems with SPI flash, or flash which
            was not erased before verification.

    config SPI_FLASH_LOG_FAILED_WRITE
        bool "Log errors if verification fails"
        depends on SPI_FLASH_VERIFY_WRITE
        default n
        help
            If this option is enabled, if SPI flash write verification fails then a log error line
            will be written with the address, expected & actual values. This can be useful when
            debugging hardware SPI flash problems.

    config SPI_FLASH_WARN_SETTING_ZERO_TO_ONE
        bool "Log warning if writing zero bits to ones"
        depends on SPI_FLASH_VERIFY_WRITE
        default n
        help
            If this option is enabled, any SPI flash write which tries to set zero bits in the flash to
            ones will log a warning. Such writes will not result in the requested data appearing identically
            in flash once written, as SPI NOR flash can only set bits to one when an entire sector is erased.
            After erasing, individual bits can only be written from one to zero.

            Note that some software (such as SPIFFS) which is aware of SPI NOR flash may write one bits as an
            optimisation, relying on the data in flash becoming a bitwise AND of the new data and any existing data.
            Such software will log spurious warnings if this option is enabled.

    config SPI_FLASH_ENABLE_COUNTERS
        bool "Enable operation counters"
        default 0
        help
            This option enables the following APIs:

            - spi_flash_reset_counters
            - spi_flash_dump_counters
            - spi_flash_get_counters

            These APIs may be used to collect performance data for spi_flash APIs
            and to help understand behaviour of libraries which use SPI flash.

    config SPI_FLASH_ROM_DRIVER_PATCH
        bool "Enable SPI flash ROM driver patched functions"
        default y
        help
            Enable this flag to use patched versions of SPI flash ROM driver functions.
            This option is needed to write to flash on ESP32-D2WD, and any configuration
            where external SPI flash is connected to non-default pins.

    choice SPI_FLASH_DANGEROUS_WRITE
        bool  "Writing to dangerous flash regions"
        default SPI_FLASH_DANGEROUS_WRITE_ABORTS
        help
            SPI flash APIs can optionally abort or return a failure code
            if erasing or writing addresses that fall at the beginning
            of flash (covering the bootloader and partition table) or that
            overlap the app partition that contains the running app.

            It is not recommended to ever write to these regions from an IDF app,
            and this check prevents logic errors or corrupted firmware memory from
            damaging these regions.

            Note that this feature *does not* check calls to the esp_rom_xxx SPI flash
            ROM functions. These functions should not be called directly from IDF
            applications.

        config SPI_FLASH_DANGEROUS_WRITE_ABORTS
            bool "Aborts"
        config SPI_FLASH_DANGEROUS_WRITE_FAILS
            bool "Fails"
        config SPI_FLASH_DANGEROUS_WRITE_ALLOWED
            bool "Allowed"
    endchoice

    config SPI_FLASH_USE_LEGACY_IMPL
        bool "Use the legacy implementation before IDF v4.0"
        default n
        help
            The implementation of SPI flash has been greatly changed in IDF v4.0.
            Enable this option to use the legacy implementation.

    config SPI_FLASH_SHARE_SPI1_BUS
        bool  "Support other devices attached to SPI1 bus"
        default n
        # The bus lock on SPI1 is meaningless when the legacy implementation is used, or the SPI
        # driver does not support SPI1.
        depends on !SPI_FLASH_USE_LEGACY_IMPL && !IDF_TARGET_ESP32S2
        select FREERTOS_SUPPORT_STATIC_ALLOCATION
        help
            Each SPI bus needs a lock for arbitration among devices. This allows multiple
            devices on a same bus, but may reduce the speed of esp_flash driver access to the
            main flash chip.

            If you only need to use esp_flash driver to access the main flash chip, disable
            this option, and the lock will be bypassed on SPI1 bus. Otherwise if extra devices
            are needed to attach to SPI1 bus, enable this option.

    config SPI_FLASH_BYPASS_BLOCK_ERASE
        bool "Bypass a block erase and always do sector erase"
        default n
        help
            Some flash chips can have very high "max" erase times, especially for block erase (32KB or 64KB).
            This option allows to bypass "block erase" and always do sector erase commands.
            This will be much slower overall in most cases, but improves latency for other code to run.

    config SPI_FLASH_YIELD_DURING_ERASE
        bool "Enables yield operation during flash erase"
        default y
        help
            This allows to yield the CPUs between erase commands.
            Prevents starvation of other tasks.

    config SPI_FLASH_ERASE_YIELD_DURATION_MS
        int "Duration of erasing to yield CPUs (ms)"
        depends on SPI_FLASH_YIELD_DURING_ERASE
        default 20
        help
            If a duration of one erase command is large
            then it will yield CPUs after finishing a current command.

    config SPI_FLASH_ERASE_YIELD_TICKS
        int "CPU release time (tick)"
        depends on SPI_FLASH_YIELD_DURING_ERASE
        default 1
        help
            Defines how many ticks will be before returning to continue a erasing.

    config SPI_FLASH_WRITE_CHUNK_SIZE
        int "Flash write chunk size"
        default 8192
        range 256 8192
        help
            Flash write is broken down in terms of multiple (smaller) write operations.
            This configuration options helps to set individual write chunk size, smaller
            value here ensures that cache (and non-IRAM resident interrupts) remains
            disabled for shorter duration.

    menu "Auto-detect flash chips"

        config SPI_FLASH_SUPPORT_ISSI_CHIP
            bool "ISSI"
            default y
            help
                Enable this to support auto detection of ISSI chips if chip vendor not directly
                given by ``chip_drv`` member of the chip struct. This adds support for variant
                chips, however will extend detecting time.

        config SPI_FLASH_SUPPORT_MXIC_CHIP
            bool "MXIC"
            default y
            help
                Enable this to support auto detection of MXIC chips if chip vendor not directly
                given by ``chip_drv`` member of the chip struct. This adds support for variant
                chips, however will extend detecting time.

        config SPI_FLASH_SUPPORT_GD_CHIP
            bool "GigaDevice"
            default y
            help
                Enable this to support auto detection of GD (GigaDevice) chips if chip vendor not
                directly given by ``chip_drv`` member of the chip struct. If you are using Wrover
                modules, please don't disable this, otherwise your flash may not work in 4-bit
                mode.

                This adds support for variant chips, however will extend detecting time and image
                size. Note that the default chip driver supports the GD chips with product ID
                60H.

    endmenu #auto detect flash chips

endmenu