OVMS3-idf/components/ethernet/eth_phy/phy_lan8720.c

// Copyright 2015-2017 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include "esp_attr.h"
#include "esp_log.h"
#include "esp_eth.h"

#include "eth_phy/phy_lan8720.h"
#include "eth_phy/phy_reg.h"

/* Value of MII_PHY_IDENTIFIER_REGs for Microchip LAN8720
 * (Except for bottom 4 bits of ID2, used for model revision)
 */
#define LAN8720_PHY_ID1 0x0007
#define LAN8720_PHY_ID2 0xc0f0
#define LAN8720_PHY_ID2_MASK 0xFFF0

/* LAN8720-specific registers */
#define SW_STRAP_CONTROL_REG       (0x9)
#define SW_STRAP_CONFIG_DONE               BIT(15)
#define AUTO_MDIX_ENABLE                   BIT(14)
#define AUTO_NEGOTIATION_ENABLE            BIT(13)
#define AN_1                               BIT(12)
#define AN_0                               BIT(11)
#define LED_CFG                            BIT(10)
#define RMII_ENHANCED_MODE                 BIT(9)

#define DEFAULT_STRAP_CONFIG (AUTO_MDIX_ENABLE|AUTO_NEGOTIATION_ENABLE|AN_1|AN_0|LED_CFG)

#define PHY_SPECIAL_CONTROL_STATUS_REG    (0x1f)
#define AUTO_NEGOTIATION_DONE              BIT(12)
#define SPEED_DUPLEX_INDICATION_10T_HALF   0x04
#define SPEED_DUPLEX_INDICATION_10T_FULL   0x14
#define SPEED_DUPLEX_INDICATION_100T_HALF  0x08
#define SPEED_DUPLEX_INDICATION_100T_FULL  0x18
#define SPEED_INDICATION_100T              BIT(3)
#define SPEED_INDICATION_10T               BIT(2)
#define DUPLEX_INDICATION_FULL             BIT(4)

static const char *TAG = "lan8720";

void phy_lan8720_check_phy_init(void)
{
    phy_lan8720_dump_registers();

    esp_eth_smi_wait_set(MII_BASIC_MODE_STATUS_REG, MII_AUTO_NEGOTIATION_COMPLETE, 0);
    esp_eth_smi_wait_set(PHY_SPECIAL_CONTROL_STATUS_REG, AUTO_NEGOTIATION_DONE, 0);
}

eth_speed_mode_t phy_lan8720_get_speed_mode(void)
{
    if(esp_eth_smi_read(PHY_SPECIAL_CONTROL_STATUS_REG) & SPEED_INDICATION_100T) {
        ESP_LOGD(TAG, "phy_lan8720_get_speed_mode(100)");
        return ETH_SPEED_MODE_100M;
    } else {
        ESP_LOGD(TAG, "phy_lan8720_get_speed_mode(10)");
        return ETH_SPEED_MODE_10M;
    }
}

eth_duplex_mode_t phy_lan8720_get_duplex_mode(void)
{
    if(esp_eth_smi_read(PHY_SPECIAL_CONTROL_STATUS_REG) & DUPLEX_INDICATION_FULL) {
        ESP_LOGD(TAG, "phy_lan8720_get_duplex_mode(FULL)");
        return ETH_MODE_FULLDUPLEX;
    } else {
        ESP_LOGD(TAG, "phy_lan8720_get_duplex_mode(HALF)");
        return ETH_MODE_HALFDUPLEX;
    }
}

void phy_lan8720_power_enable(bool enable)
{
    if (enable) {
        esp_eth_smi_write(SW_STRAP_CONTROL_REG, DEFAULT_STRAP_CONFIG | SW_STRAP_CONFIG_DONE);
        // TODO: only enable if config.flow_ctrl_enable == true
        phy_mii_enable_flow_ctrl();
    }
}

void phy_lan8720_init(void)
{
    ESP_LOGD(TAG, "phy_lan8720_init()");
    phy_lan8720_dump_registers();

    esp_eth_smi_write(MII_BASIC_MODE_CONTROL_REG, MII_SOFTWARE_RESET);

    esp_err_t res1, res2;
    do {
        // Call esp_eth_smi_wait_value() with a timeout so it prints an error periodically
        res1 = esp_eth_smi_wait_value(MII_PHY_IDENTIFIER_1_REG, LAN8720_PHY_ID1, UINT16_MAX, 1000);
        res2 = esp_eth_smi_wait_value(MII_PHY_IDENTIFIER_2_REG, LAN8720_PHY_ID2, LAN8720_PHY_ID2_MASK, 1000);
    } while(res1 != ESP_OK || res2 != ESP_OK);

    esp_eth_smi_write(SW_STRAP_CONTROL_REG,
                      DEFAULT_STRAP_CONFIG | SW_STRAP_CONFIG_DONE);


    ets_delay_us(300);

    // TODO: only enable if config.flow_ctrl_enable == true
    phy_mii_enable_flow_ctrl();
}

const eth_config_t phy_lan8720_default_ethernet_config = {
    // By default, the PHY address is 0 or 1 based on PHYAD0
    // pin. Can also be overriden in software. See datasheet
    // for defaults.
    .phy_addr = 0,
    .mac_mode = ETH_MODE_RMII,
    .clock_mode = ETH_CLOCK_GPIO0_IN,
    //Only FULLDUPLEX mode support flow ctrl now!
    .flow_ctrl_enable = true,
    .phy_init = phy_lan8720_init,
    .phy_check_init = phy_lan8720_check_phy_init,
    .phy_power_enable = phy_lan8720_power_enable,
    .phy_check_link = phy_mii_check_link_status,
    .phy_get_speed_mode = phy_lan8720_get_speed_mode,
    .phy_get_duplex_mode = phy_lan8720_get_duplex_mode,
    .phy_get_partner_pause_enable = phy_mii_get_partner_pause_enable,
};

void phy_lan8720_dump_registers()
{
    ESP_LOGD(TAG, "LAN8720 Registers:");
    ESP_LOGD(TAG, "BCR    0x%04x", esp_eth_smi_read(0x0));
    ESP_LOGD(TAG, "BSR    0x%04x", esp_eth_smi_read(0x1));
    ESP_LOGD(TAG, "PHY1   0x%04x", esp_eth_smi_read(0x2));
    ESP_LOGD(TAG, "PHY2   0x%04x", esp_eth_smi_read(0x3));
    ESP_LOGD(TAG, "ANAR   0x%04x", esp_eth_smi_read(0x4));
    ESP_LOGD(TAG, "ANLPAR 0x%04x", esp_eth_smi_read(0x5));
    ESP_LOGD(TAG, "ANER   0x%04x", esp_eth_smi_read(0x6));
    ESP_LOGD(TAG, "MCSR   0x%04x", esp_eth_smi_read(0x11));
    ESP_LOGD(TAG, "SM     0x%04x", esp_eth_smi_read(0x12));
    ESP_LOGD(TAG, "SECR   0x%04x", esp_eth_smi_read(0x1A));
    ESP_LOGD(TAG, "CSIR   0x%04x", esp_eth_smi_read(0x1B));
    ESP_LOGD(TAG, "ISR    0x%04x", esp_eth_smi_read(0x1D));
    ESP_LOGD(TAG, "IMR    0x%04x", esp_eth_smi_read(0x1E));
    ESP_LOGD(TAG, "PSCSR  0x%04x", esp_eth_smi_read(0x1F));
}