OVMS3-idf/components/soc/include/hal/adc_hal.h

207 lines
6.5 KiB
C
Raw Normal View History

2019-09-09 12:56:46 +00:00
#pragma once
#include "hal/adc_types.h"
#include "hal/adc_ll.h"
typedef struct {
bool conv_limit_en;
uint32_t conv_limit_num;
uint32_t clk_div;
uint32_t adc1_pattern_len;
uint32_t adc2_pattern_len;
adc_ll_pattern_table_t *adc1_pattern;
adc_ll_pattern_table_t *adc2_pattern;
adc_ll_convert_mode_t conv_mode;
adc_ll_dig_output_format_t format;
} adc_hal_dig_config_t;
/*---------------------------------------------------------------
Common setting
---------------------------------------------------------------*/
/**
* ADC module initialization.
*/
void adc_hal_init(void);
/**
* Set adc sample cycle for digital controller.
*
* @note Normally, please use default value.
* @param sample_cycle Cycles between DIG ADC controller start ADC sensor and beginning to receive data from sensor.
* Range: 2 ~ 0xFF.
*/
#define adc_hal_dig_set_sample_cycle(sample_cycle) adc_ll_dig_set_sample_cycle(sample_cycle)
/**
* Set ADC module power management.
*
* @prarm manage Set ADC power status.
*/
#define adc_hal_set_power_manage(manage) adc_ll_set_power_manage(manage)
/**
* Get ADC module power management.
*
* @return
* - ADC power status.
*/
#define adc_hal_get_power_manage() adc_ll_get_power_manage()
/**
* ADC module clock division factor setting. ADC clock devided from APB clock.
*
* @prarm div Division factor.
*/
#define adc_hal_set_clk_div(div) adc_ll_set_clk_div(div)
/**
* ADC module output data invert or not.
*
* @prarm adc_n ADC unit.
*/
#define adc_hal_output_invert(adc_n, inv_en) adc_ll_output_invert(adc_n, inv_en)
/**
* Set ADC module controller.
* There are five SAR ADC controllers:
* Two digital controller: Continuous conversion mode (DMA). High performance with multiple channel scan modes;
* Two RTC controller: Single conversion modes (Polling). For low power purpose working during deep sleep;
* the other is dedicated for Power detect (PWDET / PKDET), Only support ADC2.
*
* @prarm adc_n ADC unit.
* @prarm ctrl ADC controller.
*/
#define adc_hal_set_controller(adc_n, ctrl) adc_ll_set_controller(adc_n, ctrl)
/**
* Set the attenuation of a particular channel on ADCn.
*
* @note For any given channel, this function must be called before the first time conversion.
*
* The default ADC full-scale voltage is 1.1V. To read higher voltages (up to the pin maximum voltage,
* usually 3.3V) requires setting >0dB signal attenuation for that ADC channel.
*
* When VDD_A is 3.3V:
*
* - 0dB attenuaton (ADC_ATTEN_DB_0) gives full-scale voltage 1.1V
* - 2.5dB attenuation (ADC_ATTEN_DB_2_5) gives full-scale voltage 1.5V
* - 6dB attenuation (ADC_ATTEN_DB_6) gives full-scale voltage 2.2V
* - 11dB attenuation (ADC_ATTEN_DB_11) gives full-scale voltage 3.9V (see note below)
*
* @note The full-scale voltage is the voltage corresponding to a maximum reading (depending on ADC1 configured
* bit width, this value is: 4095 for 12-bits, 2047 for 11-bits, 1023 for 10-bits, 511 for 9 bits.)
*
* @note At 11dB attenuation the maximum voltage is limited by VDD_A, not the full scale voltage.
*
* Due to ADC characteristics, most accurate results are obtained within the following approximate voltage ranges:
*
* - 0dB attenuaton (ADC_ATTEN_DB_0) between 100 and 950mV
* - 2.5dB attenuation (ADC_ATTEN_DB_2_5) between 100 and 1250mV
* - 6dB attenuation (ADC_ATTEN_DB_6) between 150 to 1750mV
* - 11dB attenuation (ADC_ATTEN_DB_11) between 150 to 2450mV
*
* For maximum accuracy, use the ADC calibration APIs and measure voltages within these recommended ranges.
*
* @prarm adc_n ADC unit.
* @prarm channel ADCn channel number.
* @prarm atten The attenuation option.
*/
#define adc_hal_set_atten(adc_n, channel, atten) adc_ll_set_atten(adc_n, channel, atten)
/**
* Close ADC AMP module if don't use it for power save.
*/
#define adc_hal_amp_disable() adc_ll_amp_disable()
/*---------------------------------------------------------------
PWDET(Power detect) controller setting
---------------------------------------------------------------*/
/**
* Set adc cct for PWDET controller.
*
* @note Capacitor tuning of the PA power monitor. cct set to the same value with PHY.
* @prarm cct Range: 0 ~ 7.
*/
#define adc_hal_pwdet_set_cct(cct) adc_ll_pwdet_set_cct(cct)
/**
* Get adc cct for PWDET controller.
*
* @note Capacitor tuning of the PA power monitor. cct set to the same value with PHY.
* @return cct Range: 0 ~ 7.
*/
#define adc_hal_pwdet_get_cct() adc_ll_pwdet_get_cct()
/*---------------------------------------------------------------
RTC controller setting
---------------------------------------------------------------*/
/**
* Set adc output data format for RTC controller.
*
* @prarm adc_n ADC unit.
* @prarm bits Output data bits width option.
*/
#define adc_hal_rtc_set_output_format(adc_n, bits) adc_ll_rtc_set_output_format(adc_n, bits)
/**
* Get the converted value for each ADCn for RTC controller.
*
* @note It may be block to wait conversion finish.
* @prarm adc_n ADC unit.
* @return
* - Converted value.
*/
int adc_hal_convert(adc_ll_num_t adc_n, int channel);
/*---------------------------------------------------------------
Digital controller setting
---------------------------------------------------------------*/
/**
* Setting the digital controller.
*
* @prarm adc_hal_dig_config_t cfg Pointer to digital controller paramter.
*/
void adc_hal_dig_controller_config(const adc_hal_dig_config_t *cfg);
/**
* Set I2S DMA data source for digital controller.
*
* @param src i2s data source.
*/
#define adc_hal_dig_set_data_source(src) adc_ll_dig_set_data_source(src)
/*---------------------------------------------------------------
Hall sensor setting
---------------------------------------------------------------*/
/**
* Enable hall sensor.
*/
#define adc_hal_hall_enable() adc_ll_hall_enable()
/**
* Disable hall sensor.
*/
#define adc_hal_hall_disable() adc_ll_hall_disable()
/**
* Start hall convert and return the hall value.
*
* @return Hall value.
*/
int adc_hal_hall_convert(void);
/**
* @brief Output ADC2 reference voltage to gpio
*
* This function utilizes the testing mux exclusive to ADC2 to route the
* reference voltage one of ADC2's channels.
*
* @param[in] io GPIO number
* @return
* - true: v_ref successfully routed to selected gpio
* - false: Unsupported gpio
*/
#define adc_hal_vref_output(io) adc_ll_vref_output(io)