FreeDATA/test

Unit Test Menu

The following CTest tests cover some TNC functionality and the interface to codec2:

1. Name: audio_buffer Tests the thread safety of the audio buffer routines.
2. Name: resampler Tests FreeDATA audio resampling from 48KHz to 8KHz.
3. Name: tnc_state_machine Tests TNC transitions between states.
4. Name: helper_routines Tests various helper routines.
5. Name: py_highsnr_stdio_P_P_multi Tests a high signal-to-noise ratio (good quality) audio path using multiple codecs. (Pure python.)
6. Name: py_highsnr_stdio_P_P_datacx Tests a high signal-to-noise ratio audio path using multiple individual codecs.
7. Name: py_highsnr_stdio_P_C_datacx Tests a high signal-to-noise ratio audio path using multiple individual codecs.
8. Name: py_highsnr_stdio_C_P_datacx Tests a high signal-to-noise ratio audio path using multiple individual codecs.
9. Name: highsnr_stdio_P_C_single Tests compatibility with FreeDATA's transmit and freedv's raw data receive.
10. Name: highsnr_stdio_C_P_single Tests compatibility with freedv's raw data transmit and FreeDATA's receive.
11. Name: highsnr_stdio_P_P_single Tests a high signal-to-noise ratio audio path using multiple codecs. (Requires POSIX system.)
12. Name: highsnr_stdio_P_P_multi Tests a high signal-to-noise ratio audio path using multiple codecs. (Requires POSIX system.)

The following tests can not currently be run with GitHub's pipeline as they require the ALSA dummy device kernel module to be installed. They also do not perform reliably. These tests are slowly being replaced with equivalent pipeline-compatible tests.

1. Name: highsnr_virtual1_P_P_single_alsa Tests a high signal-to-noise ratio audio path using a single codec directly over an ALSA dummy device.
2. Name: highsnr_virtual2_P_P_single Tests a high signal-to-noise ratio audio path using a single codec over an ALSA dummy device. Not functional due to an incompatibility between the two scripts in the way they determine audio devices.
3. Name: highsnr_virtual3_P_P_multi Tests a high signal-to-noise ratio audio path using multiple codecs over an ALSA dummy device.
4. Name: highsnr_virtual4_P_P_single_callback Not functional due to an incompatibility between the two scripts in the way they determine audio devices.
5. Name: highsnr_virtual4_P_P_single_callback_outside Not functional due to an incompatibility between the two scripts in the way they determine audio devices.
6. Name: highsnr_virtual5_P_P_multi_callback
7. Name: highsnr_virtual5_P_P_multi_callback_outside
8. Name: highsnr_ARQ_short Not functional, it is an obsolete or not yet completed test.

Instructions

1. Install:

   cd FreeDATA
   mkdir build
   cd build
   cmake -DCODEC2_BUILD_DIR=$HOME/codec2/build_linux ..
   

2. List available tests:

   ctest -N
   Test project /home/david/FreeDATA/build
   Test #1: 000_audio_tests
   Test #2: 001_highsnr_stdio_audio
   
   Total Tests: 2
   

3. Run tests:

   ctest --output-on-failure
   

4. Run tests verbosely:

   ctest -V
   

001_HIGHSNR_STDIO_AUDIO TEST SUITE

1. Install

   sudo apt update
   sudo apt upgrade
   sudo apt install git cmake build-essential python3-pip portaudio19-dev python3-pyaudio
   pip3 install crcengine
   pip3 install threading
   

2. Install codec2, and set up the libcodec2.so shared library path, for example

   export LD_LIBRARY_PATH=${HOME}/codec2/build_linux/src
   

STDIO tests

Pipes are used to move audio samples from the Tx to Rx:

python3 test_tx.py --mode datac1 --delay 500 --frames 2 --bursts 1 | python3 test_rx.py --mode datac1 --frames 2 --bursts 1

AUDIO test via virtual audio devices

Important:

The virtual audio devices are great for testing, but they are also a little bit tricky to handle. So there's a high chance, the tests will fail, if you are running them via virtual audio devices. You should run the tests several times, while keeping this in mind. Most time the ctest is working even if it is failing.

1. Create virtual audio devices. Note: This command needs to be run again after every reboot

   sudo modprobe snd-aloop index=1,2 enable=1,1 pcm_substreams=1,1 id=CHAT1,CHAT2
   

2. Check if devices have been created

    aplay -l
   
    Karte 0: Intel [HDA Intel], Gerät 0: Generic Analog [Generic Analog]
      Sub-Geräte: 1/1
      Sub-Gerät #0: subdevice #0
    Karte 1: CHAT1 [Loopback], Gerät 0: Loopback PCM [Loopback PCM]
      Sub-Geräte: 1/1
      Sub-Gerät #0: subdevice #0
    Karte 1: CHAT1 [Loopback], Gerät 1: Loopback PCM [Loopback PCM]
      Sub-Geräte: 1/1
      Sub-Gerät #0: subdevice #0
    Karte 2: CHAT2 [Loopback], Gerät 0: Loopback PCM [Loopback PCM]
      Sub-Geräte: 1/1
      Sub-Gerät #0: subdevice #0
    Karte 2: CHAT2 [Loopback], Gerät 1: Loopback PCM [Loopback PCM]
      Sub-Geräte: 1/1
      Sub-Gerät #0: subdevice #0
   

3. Determine the audio device number you would like to use:

   python3 test_rx.py --list
   <snip>
   audiodev:  0 HDA Intel PCH: ALC269VC Analog (hw:0,0)
   audiodev:  1 HDA Intel PCH: HDMI 0 (hw:0,3)
   audiodev:  2 HDA Intel PCH: HDMI 1 (hw:0,7)
   audiodev:  3 HDA Intel PCH: HDMI 2 (hw:0,8)
   audiodev:  4 Loopback: PCM (hw:1,0)
   audiodev:  5 Loopback: PCM (hw:1,1)
   audiodev:  6 Loopback: PCM (hw:2,0)
   audiodev:  7 Loopback: PCM (hw:2,1)
   

   In this case we choose audiodev 4 for the RX and 5 for the Tx.

4. Start the Rx first, then Tx in separate consoles:

   python3 test_rx.py --mode datac0 --frames 2 --bursts 1 --audiodev 4 --debug
   python3 test_tx.py --mode datac0 --frames 2 --bursts 1 --audiodev 5