Crash_Override/ESP32_ChinaDieselHeater_Control
1
0
Fork 0
Code Issues Pull requests Projects Releases Wiki Activity
ESP32_ChinaDieselHeater_Con.../Arduino/BTCDieselHeater/BTCDieselHeater.ino

1142 lines
No EOL
34 KiB
C++
Raw Blame History

/*
* This file is part of the "bluetoothheater" distribution
* (https://gitlab.com/mrjones.id.au/bluetoothheater)
*
* Copyright (C) 2018 Ray Jones <ray@mrjones.id.au>
* Copyright (C) 2018 James Clark
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
/*
Chinese Heater Half Duplex Serial Data Sending Tool
Connects to the blue wire of a Chinese heater, which is the half duplex serial link.
Sends and receives data from hardware serial port 1.
Terminology: Tx is to the heater unit, Rx is from the heater unit.
Typical data frame timing on the blue wire is:
__Tx_Rx____________________________Tx_Rx____________________________Tx_Rx___________
This software can connect to the blue wire in a normal OEM system, detecting the
OEM controller and allowing extraction of the data or injecting on/off commands.
If Pin 21 is grounded on the Due, this simple stream will be reported over Serial and
no control from the Arduino will be allowed.
This allows passive sniffing of the blue wire in a normal system.
The binary data is received from the line.
If it has been > 100ms since the last blue wire activity this indicates a new frame
sequence is starting from the OEM controller.
Synchronise as such then count off the next 24 bytes storing them in the Controller's
data array. These bytes are then reported over Serial to the PC in ASCII.
It is then expected the heater will respond with it's 24 bytes.
Capture those bytes and store them in the Heater1 data array.
Once again these bytes are then reported over Serial to the PC in ASCII.
If no activity is sensed in a second, it is assumed no OEM controller is attached and we
have full control over the heater.
Either way we can now inject a message onto the blue wire allowing our custom
on/off control.
We must remain synchronous with an OEM controller if it exists otherwise E-07
faults will be caused.
Typical data frame timing on the blue wire is then:
__OEMTx_HtrRx__OurTx_HtrRx____________OEMTx_HtrRx__OurTx_HtrRx____________OEMTx_HtrRx__OurTx_HtrRx_________
The second HtrRx to the next OEMTx delay is always > 100ms and is paced by the OEM controller.
The delay before seeing Heater Rx data after any Tx is usually much less than 10ms.
But this does rise if new max/min or voltage settings are sent.
**The heater only ever sends Rx data in response to a data frame from a controller**
For Bluetooth connectivity, a HC-05 Bluetooth module is attached to Serial2:
TXD -> Rx2 (pin 17)
RXD -> Tx2 (pin 16)
EN(key) -> pin 15
STATE -> pin 4
This code only works with boards that have more than one hardware serial port like Arduino
Mega, Due, Zero, ESP32 etc.
The circuit:
- a Tx Rx multiplexer is required to combine the Arduino's Tx1 And Rx1 pins onto the blue wire.
- a Tx Enable signal from pin 22 controls the multiplexer, high for Tx, low for Rx
- Serial logging software on Serial0 via USB link
created 23 Sep 2018 by Ray Jones
This example code is in the public domain.
*/
#include <OneWire.h>
#include <Wire.h>
#include "src/cfg/BTCConfig.h"
#include "src/cfg/pins.h"
#include "src/Wifi/BTCWebServer.h"
#include "src/Wifi/BTCota.h"
#include "src/Protocol/Protocol.h"
#include "src/Protocol/TxManage.h"
#include "src/Protocol/SmartError.h"
#include "src/Protocol/helpers.h"
#include "src/Utility/NVStorage.h"
#include "src/Utility/DebugPort.h"
#include "src/Utility/UtilClasses.h"
#include "src/Utility/BTC_JSON.h"
#include "src/OLED/ScreenManager.h"
#include "src/OLED/keypad.h"
#include <DallasTemperature.h>
#include "src/RTC/Clock.h"
#if USE_SPIFFS == 1
#include <SPIFFS.h>
#endif
#define FAILEDSSID "BTCESP32"
#define FAILEDPASSWORD "thereisnospoon"
#define RX_DATA_TIMOUT 50
#ifdef ESP32
#include "src/Bluetooth/BluetoothESP32.h"
#else
#include "src/Bluetooth/BluetoothHC05.h"
#endif
// Setup Serial Port Definitions
#if defined(__arm__)
// Required for Arduino Due, UARTclass is derived from HardwareSerial
static UARTClass& BlueWireSerial(Serial1);
#else
// for ESP32, Mega
// HardwareSerial is it for these boards
static HardwareSerial& BlueWireSerial(Serial1);
#endif
void initBlueWireSerial();
bool validateFrame(const CProtocol& frame, const char* name);
void checkDisplayUpdate();
void checkDebugCommands();
// DS18B20 temperature sensor support
OneWire ds(15); // on pin 5 (a 4.7K resistor is necessary)
DallasTemperature TempSensor(&ds);
long lastTemperatureTime; // used to moderate DS18B20 access
float fFilteredTemperature = -100; // -100: force direct update uopn first pass
const float fAlpha = 0.95; // exponential mean alpha
int DS18B20holdoff = 2;
unsigned long lastAnimationTime; // used to sequence updates to LCD for animation
CommStates CommState;
CTxManage TxManage(TxEnbPin, BlueWireSerial);
CModeratedFrame OEMCtrlFrame; // data packet received from heater in response to OEM controller packet
CModeratedFrame HeaterFrame1; // data packet received from heater in response to OEM controller packet
CProtocol HeaterFrame2; // data packet received from heater in response to our packet
CProtocol DefaultBTCParams(CProtocol::CtrlMode); // defines the default parameters, used in case of no OEM controller
CSmartError SmartError;
CKeyPad KeyPad;
CScreenManager ScreenManager;
TelnetSpy DebugPort;
sRxLine PCline;
long lastRxTime; // used to observe inter character delays
bool bHasOEMController = false;
bool bHasOEMLCDController = false;
bool bHasHtrData = false;
bool bReportBlueWireData = REPORT_RAW_DATA;
bool bReportJSONData = REPORT_JSON_TRANSMIT;
bool bReportRecyleEvents = REPORT_BLUEWIRE_RECYCLES;
bool bReportOEMresync = REPORT_OEM_RESYNC;
CProtocolPackage reportHeaterData;
CProtocolPackage primaryHeaterData;
unsigned long moderator;
bool bUpdateDisplay = false;
bool bHaveWebClient = false;
bool bBTconnected = false;
////////////////////////////////////////////////////////////////////////////////////////////////////////
// Bluetooth instantiation
//
#ifdef ESP32
// Bluetooth options for ESP32
#if USE_HC05_BLUETOOTH == 1
CBluetoothESP32HC05 Bluetooth(HC05_KeyPin, HC05_SensePin, Rx2Pin, Tx2Pin); // Instantiate ESP32 using a HC-05
#elif USE_BLE_BLUETOOTH == 1
CBluetoothESP32BLE Bluetooth; // Instantiate ESP32 BLE server
#elif USE_CLASSIC_BLUETOOTH == 1
CBluetoothESP32Classic Bluetooth; // Instantiate ESP32 Classic Bluetooth server
#else // none selected
CBluetoothAbstract Bluetooth; // default no bluetooth support - empty shell
#endif
#else // !ESP32
// Bluetooth for boards other than ESP32
#if USE_HC05_BLUETOOTH == 1
CBluetoothHC05 Bluetooth(HC05_KeyPin, HC05_SensePin); // Instantiate a HC-05
#else // none selected
CBluetoothAbstract Bluetooth; // default no bluetooth support - empty shell
#endif // closing USE_HC05_BLUETOOTH
#endif // closing ESP32
//
// END Bluetooth instantiation
////////////////////////////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////////////////////////////
// setup Non Volatile storage
// this is very much hardware dependent, we can use the ESP32's FLASH
//
#ifdef ESP32
CESP32HeaterStorage actualNVstore;
#else
CHeaterStorage actualNVstore; // dummy, for now
#endif
// create reference to CHeaterStorage
// via the magic of polymorphism we can use this to access whatever
// storage is required for a specific platform in a uniform way
CHeaterStorage& NVstore = actualNVstore;
//
////////////////////////////////////////////////////////////////////////////////////////////////////////
CBluetoothAbstract& getBluetoothClient()
{
return Bluetooth;
}
// callback function for Keypad events.
// must be an absolute function, cannot be a class member due the "this" element!
void parentKeyHandler(uint8_t event)
{
ScreenManager.keyHandler(event); // call into the Screen Manager
}
const char* print18B20Address(DeviceAddress deviceAddress)
{
static char addrStr[32];
addrStr[0] = 0;
for (uint8_t i = 0; i < 8; i++)
{
char subset[8];
sprintf(subset, "%02X%c", deviceAddress[i], i<7 ? ':' : ' ');
strcat(addrStr, subset);
}
return addrStr;
}
#if USE_SPIFFS == 1
void listDir(fs::FS &fs, const char * dirname, uint8_t levels)
{
DebugPort.print("Listing directory: "); DebugPort.println(dirname);
File root = fs.open(dirname);
if (!root) {
DebugPort.println("Failed to open directory");
return;
}
if (!root.isDirectory()) {
DebugPort.println("Not a directory");
return;
}
File file = root.openNextFile();
while (file) {
if (file.isDirectory()) {
DebugPort.print(" DIR : ");
DebugPort.println(file.name());
if (levels) {
listDir(fs, file.name(), levels - 1);
}
} else {
DebugPort.print(" FILE: ");
DebugPort.print(file.name());
DebugPort.print(" SIZE: ");
DebugPort.println(file.size());
}
file = root.openNextFile();
}
}
#endif
void setup() {
char msg[128];
TempSensor.begin();
// initialise TelnetSpy (port 23) as well as Serial to 115200
// Serial is the usual USB connection to a PC
// DO THIS BEFORE WE TRY AND SEND DEBUG INFO!
DebugPort.setWelcomeMsg("*************************************************\r\n"
"* Connected to BTC heater controller debug port *\r\n"
"*************************************************\r\n");
DebugPort.setBufferSize(8192);
DebugPort.begin(115200);
DebugPort.println("_______________________________________________________________");
DebugPort.println("DS18B20 status dump");
sprintf(msg, " Temperature for device#1 (idx 0) is: %.1f", TempSensor.getTempCByIndex(0));
DebugPort.println(msg);
#if USE_SPIFFS == 1
// Initialize SPIFFS
if(!SPIFFS.begin(true)){
DebugPort.println("An Error has occurred while mounting SPIFFS");
}
else {
DebugPort.println("Mounted SPIFFS OK");
listDir(SPIFFS, "/", 2);
}
#endif
// locate devices on the bus
DebugPort.print("Locating DS18B20 devices...");
// initialise DS18B20 temperature sensor(s)
// Grab a count of devices on the wire
int numberOfDevices = TempSensor.getDeviceCount();
sprintf(msg, " Found %d devices", numberOfDevices);
DebugPort.println(msg);
// report parasite power requirements
sprintf(msg, " Parasite power is: %s", TempSensor.isParasitePowerMode() ? "ON" : "OFF");
DebugPort.println(msg);
// Loop through each device, print out address
for(int i=0;i<numberOfDevices; i++)
{
// Search the wire for address
DeviceAddress tempDeviceAddress;
if(TempSensor.getAddress(tempDeviceAddress, i)) {
sprintf(msg, " Found DS18B20 device#%d with address: %s", i+1, print18B20Address(tempDeviceAddress));
DebugPort.println(msg);
sprintf(msg, " Resolution: %d bits", TempSensor.getResolution(tempDeviceAddress));
DebugPort.println(msg);
} else {
sprintf(msg, " Found ghost @ device#%d, but could not detect address. Check power and cabling", i+1);
DebugPort.println(msg);
}
}
TempSensor.setWaitForConversion(false);
TempSensor.requestTemperatures();
lastTemperatureTime = millis();
lastAnimationTime = millis();
NVstore.init();
NVstore.load();
KeyPad.begin(keyLeft_pin, keyRight_pin, keyCentre_pin, keyUp_pin, keyDown_pin);
KeyPad.setCallback(parentKeyHandler);
// Initialize the rtc object
Clock.begin();
bool bNoClock = true;
const BTCDateTime& now = Clock.get();
if(now.day() != 0xa5)
bNoClock = false;
ScreenManager.begin(bNoClock);
#if USE_WIFI == 1
initWifi(WiFi_TriggerPin, FAILEDSSID, FAILEDPASSWORD);
#if USE_OTA == 1
initOTA();
#endif // USE_OTA
#if USE_WEBSERVER == 1
initWebServer();
#endif // USE_WEBSERVER
#endif // USE_WIFI
pinMode(ListenOnlyPin, INPUT_PULLUP); // pin to enable passive mode
pinMode(LED_Pin, OUTPUT); // On board LED indicator
digitalWrite(LED_Pin, LOW);
initBlueWireSerial();
// prepare for first long delay detection
lastRxTime = millis();
TxManage.begin(); // ensure Tx enable pin is setup
// define defaults should OEM controller be missing
DefaultBTCParams.setTemperature_Desired(23);
DefaultBTCParams.setTemperature_Actual(22);
DefaultBTCParams.setSystemVoltage(12.0);
DefaultBTCParams.setPump_Min(1.6f);
DefaultBTCParams.setPump_Max(5.5f);
DefaultBTCParams.setFan_Min(1680);
DefaultBTCParams.setFan_Max(4500);
DefaultBTCParams.Controller.FanSensor = 1;
bBTconnected = false;
Bluetooth.begin();
}
// main functional loop is based about a state machine approach, waiting for data
// to appear upon the blue wire, and marshalling into an appropriate receive buffers
// according to the state.
void loop()
{
float fTemperature;
unsigned long timenow = millis();
DebugPort.handle(); // keep telnet spy alive
#if USE_WIFI == 1
doWiFiManager();
#if USE_OTA == 1
DoOTA();
#endif // USE_OTA
#if USE_WEBSERVER == 1
bHaveWebClient = doWebServer();
#endif //USE_WEBSERVER
#endif // USE_WIFI
checkDebugCommands();
KeyPad.update(); // scan keypad - key presses handler via callback functions!
Bluetooth.check(); // check for Bluetooth activity
// manage changes in Bluetooth connection status
if(Bluetooth.isConnected()) {
if(!bBTconnected) {
resetJSONmoderator(); // force full send upon BT client connect
}
bBTconnected = true;
}
else {
bBTconnected = false;
}
// manage changes in number of wifi clients
if(isWebServerClientChange()) {
resetJSONmoderator(); // force full send upon number of Wifi clients change
}
//////////////////////////////////////////////////////////////////////////////////////
// Blue wire data reception
// Reads data from the "blue wire" Serial port, (to/from heater)
// If an OEM controller exists we will also see it's data frames
// Note that the data is read now, then held for later use in the state machine
//
sRxData BlueWireData;
// calc elapsed time since last rxd byte
// used to detect no OEM controller, or the start of an OEM frame sequence
unsigned long RxTimeElapsed = timenow - lastRxTime;
if (BlueWireSerial.available()) {
// Data is avaialable, read and store it now, use it later
// Note that if not in a recognised data receive frame state, the data
// will be deliberately lost!
BlueWireData.setValue(BlueWireSerial.read()); // read hex byte, store for later use
lastRxTime = timenow; // tickle last rx time, for rx data timeout purposes
}
// precautionary state machine action if all 24 bytes were not received
// whilst expecting a frame from the blue wire
if(RxTimeElapsed > RX_DATA_TIMOUT) {
if( CommState.is(CommStates::OEMCtrlRx) ||
CommState.is(CommStates::HeaterRx1) ||
CommState.is(CommStates::HeaterRx2) ) {
if(RxTimeElapsed >= moderator) {
moderator += 10;
if(bReportRecyleEvents) {
DebugPort.print(RxTimeElapsed);
DebugPort.print("ms - ");
}
if(CommState.is(CommStates::OEMCtrlRx)) {
bHasOEMController = false;
bHasOEMLCDController = false;
if(bReportRecyleEvents)
DebugPort.println("Timeout collecting OEM controller data, returning to Idle State");
}
else if(CommState.is(CommStates::HeaterRx1)) {
bHasHtrData = false;
if(bReportRecyleEvents)
DebugPort.println("Timeout collecting OEM heater response data, returning to Idle State");
}
else {
bHasHtrData = false;
if(bReportRecyleEvents)
DebugPort.println("Timeout collecting BTC heater response data, returning to Idle State");
}
}
if(bReportRecyleEvents)
DebugPort.println("Recycling blue wire serial interface");
initBlueWireSerial();
CommState.set(CommStates::TemperatureRead); // revert to idle mode, after passing thru temperature mode
}
}
///////////////////////////////////////////////////////////////////////////////////////////
// do our state machine to track the reception and delivery of blue wire data
long tDelta;
switch(CommState.get()) {
case CommStates::Idle:
moderator = 50;
#if RX_LED == 1
digitalWrite(LED_Pin, LOW);
#endif
// Detect the possible start of a new frame sequence from an OEM controller
// This will be the first activity for considerable period on the blue wire
// The heater always responds to a controller frame, but otherwise never by itself
if(RxTimeElapsed >= 970) {
// have not seen any receive data for a second.
// OEM controller is probably not connected.
// Skip state machine immediately to BTC_Tx, sending our own settings.
bHasHtrData = false;
bHasOEMController = false;
bHasOEMLCDController = false;
bool isBTCmaster = true;
TxManage.PrepareFrame(DefaultBTCParams, isBTCmaster); // use our parameters, and mix in NV storage values
TxManage.Start(timenow);
CommState.set(CommStates::BTC_Tx);
break;
}
#if SUPPORT_OEM_CONTROLLER == 1
if(BlueWireData.available() && (RxTimeElapsed > RX_DATA_TIMOUT+10)) {
if(bReportOEMresync) {
DebugPort.print("Re-sync'd with OEM Controller. ");
DebugPort.print(RxTimeElapsed);
DebugPort.println("ms Idle time.");
}
bHasHtrData = false;
bHasOEMController = true;
CommState.set(CommStates::OEMCtrlRx); // we must add this new byte!
//
// ** IMPORTANT - we must drop through to OEMCtrlRx *NOW* (skipping break) **
// ** otherwise the first byte will be lost! **
//
}
else {
Clock.update();
checkDisplayUpdate();
break; // only break if we fail all Idle state tests
}
#else
Clock.update();
checkDisplayUpdate();
break;
#endif
case CommStates::OEMCtrlRx:
#if RX_LED == 1
digitalWrite(LED_Pin, HIGH);
#endif
// collect OEM controller frame
if(BlueWireData.available()) {
if(CommState.collectData(OEMCtrlFrame, BlueWireData.getValue()) ) {
CommState.set(CommStates::OEMCtrlValidate); // collected 24 bytes, move on!
}
}
break;
case CommStates::OEMCtrlValidate:
#if RX_LED == 1
digitalWrite(LED_Pin, LOW);
#endif
// test for valid CRC, abort and restarts Serial1 if invalid
if(!validateFrame(OEMCtrlFrame, "OEM")) {
break;
}
// filled OEM controller frame
OEMCtrlFrame.setTime();
// LCD controllers use 0x76 as first byte, rotary knobs use 0x78
bHasOEMLCDController = (OEMCtrlFrame.Controller.Byte0 != 0x78);
CommState.set(CommStates::HeaterRx1);
break;
case CommStates::HeaterRx1:
#if RX_LED == 1
digitalWrite(LED_Pin, HIGH);
#endif
// collect heater frame, always in response to an OEM controller frame
if(BlueWireData.available()) {
if( CommState.collectData(HeaterFrame1, BlueWireData.getValue()) ) {
CommState.set(CommStates::HeaterValidate1);
}
}
break;
case CommStates::HeaterValidate1:
#if RX_LED == 1
digitalWrite(LED_Pin, LOW);
#endif
// test for valid CRC, abort and restarts Serial1 if invalid
if(!validateFrame(HeaterFrame1, "RX1")) {
bHasHtrData = false;
break;
}
bHasHtrData = true;
// received heater frame (after controller message), report
// do some monitoring of the heater state variable
// if abnormal transitions, introduce a smart error!
// This routine also cancels ON/OFF requests if runstate in startup/shutdown periods
SmartError.monitor(HeaterFrame1);
HeaterFrame1.setTime();
while(BlueWireSerial.available()) {
DebugPort.println("DUMPED ROGUE RX DATA");
BlueWireSerial.read();
}
BlueWireSerial.flush();
primaryHeaterData.set(HeaterFrame1, OEMCtrlFrame); // OEM is always *the* controller
if(bReportBlueWireData) {
primaryHeaterData.reportFrames(true);
CommState.setDelay(20); // let serial get sent before we send blue wire
}
else {
CommState.setDelay(0);
}
CommState.set(CommStates::HeaterReport1);
break;
case CommStates::HeaterReport1:
if(CommState.delayExpired()) {
if(digitalRead(ListenOnlyPin)) { // pin open, pulled high (STANDARD OPERATION)
bool isBTCmaster = false;
TxManage.PrepareFrame(OEMCtrlFrame, isBTCmaster); // parrot OEM parameters, but block NV modes
TxManage.Start(timenow);
CommState.set(CommStates::BTC_Tx);
}
else { // pin shorted to ground
CommState.set(CommStates::TemperatureRead); // "Listen Only" input is held low, don't send our Tx
}
}
break;
case CommStates::BTC_Tx:
// Handle time interval where we send data to the blue wire
lastRxTime = timenow; // *we* are pumping onto blue wire, track this activity!
if(TxManage.CheckTx(timenow) ) { // monitor progress of our data delivery
CommState.set(CommStates::HeaterRx2); // then await heater repsonse
}
break;
case CommStates::HeaterRx2:
#if RX_LED == 1
digitalWrite(LED_Pin, HIGH);
#endif
// collect heater frame, in response to our control frame
if(BlueWireData.available()) {
#ifdef BADSTARTCHECK
if(!CommState.checkValidStart(BlueWireData.getValue())) {
DebugPort.println("***** Invalid start of frame - restarting Serial port *****");
initBlueWireSerial();
CommState.set(CommStates::Idle);
}
else {
if( CommState.collectData(HeaterFrame2, BlueWireData.getValue()) ) {
CommState.set(CommStates::HeaterValidate2);
}
}
#else
if( CommState.collectData(HeaterFrame2, BlueWireData.getValue()) ) {
CommState.set(CommStates::HeaterValidate2);
}
#endif
}
break;
case CommStates::HeaterValidate2:
#if RX_LED == 1
digitalWrite(LED_Pin, LOW);
#endif
// test for valid CRC, abort and restart Serial1 if invalid
if(!validateFrame(HeaterFrame2, "RX2")) {
bHasHtrData = false;
break;
}
bHasHtrData = true;
// received heater frame (after our control message), report
// do some monitoring of the heater state variables
// if abnormal transitions, introduce a smart error!
SmartError.monitor(HeaterFrame2);
if(!bHasOEMController) // no OEM controller - BTC is *the* controller
primaryHeaterData.set(HeaterFrame2, TxManage.getFrame());
if(bReportBlueWireData) {
reportHeaterData.set(HeaterFrame2, TxManage.getFrame());
reportHeaterData.reportFrames(false);
CommState.setDelay(20); // let serial get sent before we send blue wire
}
else {
CommState.setDelay(0);
}
CommState.set(CommStates::HeaterReport2);
break;
case CommStates::HeaterReport2:
if(CommState.delayExpired()) {
CommState.set(CommStates::TemperatureRead);
}
break;
case CommStates::TemperatureRead:
// update temperature reading,
// synchronised with serial reception as interrupts do get disabled in the OneWire library
tDelta = timenow - lastTemperatureTime;
if(tDelta > TEMPERATURE_INTERVAL) { // maintain a minimum holdoff period
lastTemperatureTime += TEMPERATURE_INTERVAL; // reset time to observe temeprature
fTemperature = TempSensor.getTempCByIndex(0); // read sensor
// DebugPort.print("DS18B20 = "); DebugPort.println(fTemperature);
// initialise filtered temperature upon very first pass
if(fTemperature > -80) { // avoid disconnected sensor readings being integrated
if(DS18B20holdoff)
DS18B20holdoff--; // first value upon sensor connect is bad
else {
if(fFilteredTemperature < -90) { // avoid FP exactness issues - starts as -100 on boot
fFilteredTemperature = fTemperature; // prime with first *valid* reading
}
// exponential mean to stabilse readings
fFilteredTemperature = fFilteredTemperature * fAlpha + (1-fAlpha) * fTemperature;
}
}
else {
DS18B20holdoff = 2;
fFilteredTemperature = -100;
}
DefaultBTCParams.setTemperature_Actual((unsigned char)(fFilteredTemperature + 0.5)); // update [BTC] frame to send
// Added DISABLE INTERRUPTS to test for parasitic fix.
// portDISABLE_INTERRUPTS();
TempSensor.requestTemperatures(); // prep sensor for future reading
// portENABLE_INTERRUPTS();
ScreenManager.reqUpdate();
}
updateJSONclients(bReportJSONData);
CommState.set(CommStates::Idle);
break;
} // switch(CommState)
BlueWireData.reset(); // ensure we flush any used data
} // loop
void DebugReportFrame(const char* hdr, const CProtocol& Frame, const char* ftr)
{
DebugPort.print(hdr); // header
for(int i=0; i<24; i++) {
char str[16];
sprintf(str, " %02X", Frame.Data[i]); // build 2 dig hex values
DebugPort.print(str); // and print
}
DebugPort.print(ftr); // footer
}
void initBlueWireSerial()
{
// initialize serial port to interact with the "blue wire"
// 25000 baud, Tx and Rx channels of Chinese heater comms interface:
// Tx/Rx data to/from heater,
// Note special baud rate for Chinese heater controllers
#if defined(__arm__) || defined(__AVR__)
BlueWireSerial.begin(25000);
pinMode(Rx1Pin, INPUT_PULLUP); // required for MUX to work properly
#elif ESP32
// ESP32
BlueWireSerial.begin(25000, SERIAL_8N1, Rx1Pin, Tx1Pin); // need to explicitly specify pins for pin multiplexer!
pinMode(Rx1Pin, INPUT_PULLUP); // required for MUX to work properly
#endif
}
bool validateFrame(const CProtocol& frame, const char* name)
{
if(!frame.verifyCRC()) {
// Bad CRC - restart blue wire Serial port
DebugPort.print("\007Bad CRC detected for ");
DebugPort.print(name);
DebugPort.println(" frame - restarting blue wire's serial port");
DebugReportFrame("BAD CRC:", frame, "\r\n");
initBlueWireSerial();
CommState.set(CommStates::TemperatureRead);
return false;
}
return true;
}
void requestOn()
{
TxManage.queueOnRequest();
SmartError.reset();
// HeaterData.setRefTime();
}
void requestOff()
{
TxManage.queueOffRequest();
SmartError.inhibit();
// HeaterData.setRefTime();
}
void ToggleOnOff()
{
if(primaryHeaterData.getRunState()) {
DebugPort.println("ToggleOnOff: Heater OFF");
requestOff();
}
else {
DebugPort.println("ToggleOnOff: Heater ON");
requestOn();
}
}
bool reqTemp(unsigned char newTemp)
{
if(bHasOEMController)
return false;
unsigned char max = DefaultBTCParams.getTemperature_Max();
unsigned char min = DefaultBTCParams.getTemperature_Min();
if(newTemp >= max)
newTemp = max;
if(newTemp <= min)
newTemp = min;
NVstore.setDesiredTemperature(newTemp);
ScreenManager.reqUpdate();
return true;
}
bool reqTempDelta(int delta)
{
unsigned char newTemp = getSetTemp() + delta;
return reqTemp(newTemp);
}
int getSetTemp()
{
return NVstore.getDesiredTemperature();
}
bool reqThermoToggle()
{
return setThermostatMode(getThermostatMode() ? 0 : 1);
}
bool setThermostatMode(unsigned char val)
{
if(bHasOEMController)
return false;
NVstore.setThermostatMode(val);
return true;
}
bool getThermostatMode()
{
return NVstore.getThermostatMode() != 0;
}
void checkDisplayUpdate()
{
// only update OLED when not processing blue wire
if(ScreenManager.checkUpdate()) {
lastAnimationTime = millis() + 100;
ScreenManager.animate();
ScreenManager.refresh(); // always refresh post major update
}
long tDelta = millis() - lastAnimationTime;
if(tDelta >= 100) {
lastAnimationTime = millis() + 100;
if(ScreenManager.animate())
ScreenManager.refresh();
}
}
void reqPumpPrime(bool on)
{
DefaultBTCParams.setPump_Prime(on);
}
float getActualTemperature()
{
return fFilteredTemperature;
}
void setPumpMin(float val)
{
NVstore.setPmin(val);
}
void setPumpMax(float val)
{
NVstore.setPmax(val);
}
void setFanMin(short cVal)
{
NVstore.setFmin(cVal);
}
void setFanMax(short cVal)
{
NVstore.setFmax(cVal);
}
void setFanSensor(unsigned char cVal)
{
NVstore.setFanSensor(cVal);
}
void setSystemVoltage(float val) {
NVstore.setSystemVoltage(val);
}
void setGlowDrive(unsigned char val) {
NVstore.setGlowDrive(val);
}
void saveNV()
{
NVstore.save();
}
const CProtocolPackage& getHeaterInfo()
{
return primaryHeaterData;
}
bool isWebClientConnected()
{
return bHaveWebClient;
}
void checkDebugCommands()
{
// check for test commands received from PC Over USB
if(DebugPort.available()) {
static int mode = 0;
static int val = 0;
char rxVal = DebugPort.read();
rxVal = toLowerCase(rxVal);
#ifdef PROTOCOL_INVESTIGATION
bool bSendVal = false;
#endif
if(isControl(rxVal)) { // "End of Line"
#ifdef PROTOCOL_INVESTIGATION
String convert(PCline.Line);
val = convert.toInt();
bSendVal = true;
PCline.clear();
#endif
}
else {
if(rxVal == ' ') { // SPACE to bring up menu
DebugPort.print("\014");
DebugPort.println("MENU options");
DebugPort.println("");
DebugPort.print(" <B> - toggle raw blue wire data reporting, currently "); DebugPort.println(bReportBlueWireData ? "ON" : "OFF");
DebugPort.print(" <J> - toggle output JSON reporting, currently "); DebugPort.println(bReportJSONData ? "ON" : "OFF");
DebugPort.print(" <W> - toggle reporting of blue wire timeout/recycling event, currently "); DebugPort.println(bReportRecyleEvents ? "ON" : "OFF");
DebugPort.print(" <O> - toggle reporting of OEM resync event, currently "); DebugPort.println(bReportOEMresync ? "ON" : "OFF");
DebugPort.print(" <S> - toggle reporting of state machine transits "); DebugPort.println(bReportOEMresync ? "ON" : "OFF");
DebugPort.println(" <+> - request heater turns ON");
DebugPort.println(" <-> - request heater turns OFF");
DebugPort.println(" <R> - restart the ESP");
DebugPort.println("");
DebugPort.println("");
DebugPort.println("");
DebugPort.println("");
DebugPort.println("");
DebugPort.println("");
DebugPort.println("");
}
#ifdef PROTOCOL_INVESTIGATION
else if(isDigit(rxVal)) {
PCline.append(rxVal);
}
else if(rxVal == 'p') {
DebugPort.println("Test Priming Byte... ");
mode = 1;
}
else if(rxVal == 'g') {
DebugPort.println("Test glow power byte... ");
mode = 2;
}
else if(rxVal == 'i') {
DebugPort.println("Test fan bytes");
mode = 3;
}
else if(rxVal == ']') {
val++;
bSendVal = true;
}
else if(rxVal == '[') {
val--;
bSendVal = true;
}
#endif
else if(rxVal == 'b') {
bReportBlueWireData = !bReportBlueWireData;
DebugPort.print("Toggled raw blue wire data reporting "); DebugPort.println(bReportBlueWireData ? "ON" : "OFF");
}
else if(rxVal == 'j') {
bReportJSONData = !bReportJSONData;
DebugPort.print("Toggled JSON data reporting "); DebugPort.println(bReportJSONData ? "ON" : "OFF");
}
else if(rxVal == 'w') {
bReportRecyleEvents = !bReportRecyleEvents;
DebugPort.print("Toggled blue wire recycling event reporting "); DebugPort.println(bReportRecyleEvents ? "ON" : "OFF");
}
else if(rxVal == 'o') {
bReportOEMresync = !bReportOEMresync;
DebugPort.print("Toggled OEM resync event reporting "); DebugPort.println(bReportOEMresync ? "ON" : "OFF");
}
else if(rxVal == 's') {
CommState.toggleReporting();
}
else if(rxVal == '+') {
TxManage.queueOnRequest();
// HeaterData.setRefTime();
}
else if(rxVal == '-') {
TxManage.queueOffRequest();
// HeaterData.setRefTime();
}
else if(rxVal == 'r') {
ESP.restart(); // reset the esp
}
}
#ifdef PROTOCOL_INVESTIGATION
if(bSendVal) {
switch(mode) {
case 1:
DefaultBTCParams.Controller.Prime = val & 0xff; // always 0x32:Thermostat, 0xCD:Fixed
break;
case 2:
DefaultBTCParams.Controller.MinTempRise = val & 0xff; // always 0x05
break;
case 3:
DefaultBTCParams.Controller.Unknown2_MSB = (val >> 8) & 0xff; // always 0x0d
DefaultBTCParams.Controller.Unknown2_LSB = (val >> 0) & 0xff; // always 0xac 16bit: "3500" ?? Ignition fan max RPM????
break;
}
}
#endif
}
}
// 0x00 - Normal: BTC, with heater responding
// 0x01 - Error: BTC, heater not responding
// 0x02 - Special: OEM controller & heater responding
// 0x03 - Error: OEM controller, heater not responding
int getBlueWireStat()
{
int stat = 0;
if(!bHasHtrData) {
stat |= 0x01;
}
if(bHasOEMController) {
stat |= 0x02;
}
return stat;
}
const char* getBlueWireStatStr()
{
const char* BlueWireStates[] = { "BTC,Htr", "BTC", "OEM,Htr", "OEM" };
return BlueWireStates[getBlueWireStat()];
}
bool hasOEMcontroller()
{
return bHasOEMController;
}
bool hasOEMLCDcontroller()
{
return bHasOEMLCDController;
}
int getSmartError()
{
return SmartError.getError();
}
Reference in a new issue View git blame Copy permalink